Support this website by joining the Silver Rails TrainWeb Club for as little as $1 per month. Click here for info.



This website has been archived from TrainWeb.org/screamingeagle to TrainWeb.US/screamingeagle.

Return HOME Return to MOPAC POWER MENU EMD SD Locomotives Return HOME
   HOME    Power     Cabooses     Rolling Stock     MoW     Depots    
MISSOURI PACIFIC EMD SD LOCOMOTIVES
The following is reproduced from actual operating manuals




SD40     25 Units
Horsepower:  3000     Weight: 389,910 lbs.     Engine: 16-645E-3 V-Type Turbocharged      Fuel Capacity:  3,250 gals.     Gear Ratio: 62:15    

Minimum Continuous Speed: 12.0 mph    Cooling Water Capacity: 254 gals.    Tractive Effort: 97,475   Sand Capacity: 56 cubic feet      

Lube Oil Capacity: 243 gals.




SD40-2: 207 Units      SD40-2c: 74 Units
Horsepower:
  3000     Weight: 390,600 lbs.     Engine: 16-645E-3 V-Type Turbocharged      Fuel Capacity:  3,250 gals.     Gear Ratio: 62:15    

Minimum Continuous Speed: 12.0 mph    Cooling Water Capacity: 275 gals.    Tractive Effort: 97,650   Sand Capacity: 56 cubic feet      

Lube Oil Capacity: 243 gals.




SD50:  60 Units
Horsepower:
  3600     Weight: 368,000 lbs.     Engine: 16-645F3B Turbocharged      Fuel Capacity:  4,500 gals.     Gear Ratio: 70:17    

Minimum Continuous Speed: 12.0 mph    Cooling Water Capacity: 288 gals.    Tractive Effort: 91,980   Sand Capacity: 56 cubic feet      

Lube Oil Capacity: 294 gals.





EMD CONTROL STANDS
Based on the EMD SD40 and SD40-2 model locomotives

The EMD SD40 Control Stand
The AAR-EMD SD40-2 and SD50 Control Stand



The EMD Control Stand were equipped on NON Dash-2 units such as the SD40s, GP35s and GP38s.

The Selector Lever has three (3) positions which are # 1, OFF and B. The Selector Lever on the controlling unit must be in the # 1 position for power, B position for dynamic braking and OFF position when locomotive is parked. On trailing units, the lever is always in the OFF position. This lever is spring loaded and returns to center position after each movement. Its position is indicated by a small illuminated window in the top left corner of the control stand.

A few units after June 1971 have three (3) position selector levers (PWR, OFF, and B). The lever is placed in the PWR position for power, B for dynamic braking, and OFF when locomotive is parked. On trailing units, it is in the OFF position. The lever is NOT spring loaded and remains in the position it was placed. Its position is indicated in an illuminated window located directly above the selector lever.

The Reverse Lever has three (3) positions which are Forward, Neutral and Reverse. The position of the reverse lever on the controlling unit controls the direction of movement. The reverse lever is removed from the control stand on trailing units to lock the throttle and selector levers.

The Throttle Lever is used for both power (when selector lever is in #1 position) and dynamic brake (when selector lever is in B position). It has 10 positions: STOP, IDLE and 1 thru 8.

The throttle is placed in the STOP position by pulling the throttle lever outward (away from control stand) and moving it forward from IDLE to STOP. This position shuts down all units in the consist except when isolation switch of an individual unit is in START position.

The throttle placed in the IDLE position will be at idle engine speed and power is not developed.

Positions 1 thru 8 power will increase the diesel engine speed and develop a predetermined power output.

Using the dynamic braking is notchless on the throttle in runs 1 thru 8.


EMD NON Dash-2 Control Panel
EMD Dash-2 Control Panel

 


The AAR Standard Engineers Control Stand was used on ALL of the EMD Dash-2 series locomotives, as well as on the GE Series-7 units. This helped avoid confusion by having to learn several different types of control stands for different models of locomotives. This control stand was also installed on many of the older EMD units on major roads in the late 1970s and early 1980s.

The Reverser Lever has three positions: Forward, Neutral (center position) and reverse. The position of the reverser lever on the controlling unit controls the direction of movement (forward or reverse).
            
When the reverse lever is in neutral position, the throttle can be moved into any position. The dynamic brake lever cannot be be moved from the OFF position unless unless the reverse lever is in forward or reverse position.

The reverser lever can be removed from the control stand when it is in the neutral position. When removed, it locks both the throttle and dynamic brake levers in idle and off positions. The reverser lever is to be removed from the control stand on all trailing units in a locomotive consist.



The Throttle Lever has ten positions: STOP, Idle, and Eight (8) power positions.

The throttle is placed in the STOP position by pulling the throttle lever outward, away from the control stand, and moving it forward from idle to stop. This position shuts down all units in the locomotive consist except when the engine control switch is in START position.

The idle position allows the engine to run at idle speed, but no power is developed.

Positions 1-8 will increase the engine speed. In each throttle position a predetermined ampere output is developed.


The Dynamic Brake Lever has three (3) positions: OFF, Set-up, and Braking Zone.

OFF is when the lever is placed in this position when dynamic brakes are not being used.

Set-up establishes the dynamic braking circuits.

Braking Zone: This zone is numbered 1 to 8. The braking effort is increased as the lever is advanced through the braking zone.





DYNAMIC BRAKES
Most of the Missouri Pacific locomotives did not have dynamic brakes, however, there were some that did contain this feature such as the SD40-2c (6000 Series Units) and some ex-Western Pacific units. In addition, the Mo-Pac often used pool power from other roads, whose power consisted of units with dynamic brakes. A brief explanation of the varieties of dynamic brakes is listed here.

Standard Range Dynamic Brake
is the amount of retarding force developed as this brake increases with the increase of the locomotive speed, reaching the maximum retarding force at approximately 23 mph (with the 62:15 gear ratio). As speed increases above 23 mph the retarding force will reduce gradually.

Extended Range Dynamic Brake provides maximum retarding force in the entire speed range between 6 and 23 mph. This feature works in conjunction with the Standard Range Dynamic Brake.

When an engineer changes operation from power to dynamic brake, he places the throttle in the Idle position and must wait a minimum of 10 seconds before applying the dynamic brake.


A Standard EMD SD40 Locomotive

 

Return HOME
          trainweb.us/screamingeagle l Last Update to this page: 16 April, 2008
          All images & text © 2000-2008 T. Greuter / Screaming Eagles, unless otherwise noted. All Rights Reserved.
ad pos61 ad pos63
ad pos62 ad pos64



Support this website by joining the Silver Rails TrainWeb Club for as little as $1 per month. Click here for info.